KIA Sportazh - Kia Sportage
Controls and operation receptions
Current leaving and service
The engine
   Check компрессионного pressure, an estimation of a condition of cylinders
   Check of the engine by means of the vacuum gauge
   Belts of a drive of auxiliary units
   Petrol models
   Diesel models
      Greasing system - the general information
      Removal and engine installation
      Removal and installation of components of drive ГРМ
      Check and adjustment клапанных backlashes
      Removal and installation of the inlet pipeline and final collector
      Service of a head of cylinders and components газораспределительного the mechanism
      Dismantling and assemblage of the block of cylinders, service of components
      Removal and pallet installation картера
      Removal, installation and service of the oil pump
      Removal and installation маслоохладителя
      Removal and flywheel installation
      Removal and installation маслораспылителей
      Replacement of epiploons of a cranked shaft
Systems of cooling, heating, ventilation and air conditioning
Power supply systems, managements of the engine/decrease of toxicity of the fulfilled gases and release of the fulfilled gases
Systems of an electric equipment of the engine
Five-step manual box of a gear change
Automatic transmission
Transmissionnaja line
Brake system
Suspension bracket and steering
Body
Onboard electric equipment
Control кузовные the sizes
Schemes of electric connections




Kia Sportage>> The engine>> Diesel models>> Removal and pallet installation картера

Removal and pallet installation картера

Details of installation of the pallet картера and the oil pump

1— The Cogwheel of a cranked shaft
2— The Pallet картера

3 — Maslozabornik with mesh the filter
4 — Maslootrazhatel
5 — the Oil pump

Removal

 PERFORMANCE ORDER

  1. Disconnect a negative wire from the battery.
  2. Hang out the car over the earth.
  3. Merge impellent oil (Current leaving and service see the Head), then screw into place and tighten with demanded effort a drain stopper, - in case of need replace its sealing washer.
  1. Hooking thin шпателем, or other suitable tool, accurately separate the pallet from маслоотражателя, - try not to bend a fixing flange of the pallet and not to damage маслозаборную a tube.

At all do not enter an edge шпателя between маслоотражателем and an interfaced surface of the block!


  1. Turn out four fixing bolts and remove equipped with the mesh filter маслозаборник, - try not to bend маслоотражатель and not to damage маслозаборную a tube.
  1. Turn out fixture and accurately remove маслоотражатель.
  1. Carefully clear interfaced surfaces of the removed components, completely having removed from them traces of oil, a dirt and the rests of old hermetic.
  2. Examine the pallet on presence of cracks, deformations and other mechanical damages. In case of need make corresponding regenerative repair, or replace the pallet.
  1. Estimate a condition of a drain stopper of the pallet, in case of need make its replacement.

It will be reasonable to replace a sealing washer of a drain stopper without dependence from its condition.

  1. Check up a condition маслоотражателя and the mesh filter маслозаборника. Carefully clean components, in case of revealing of irreversible damages make replacement.

Installation

The size выступания the pallet for borders of a face surface картера the engine should not exceed 1.5 mm.


 PERFORMANCE ORDER

  1. Impose a pillow of hermetic of type Loctite Ultra Blue 5900 section of diameter of 2-4 mm on an interfaced surface of a landing flange маслоотражателя and press last to картеру the engine, the interfaced which surface also should be smoothed carefully out and degreased. Track, that hermetic was imposed from the interior of fixing apertures and with a tipping over on the ends. Establish маслоотражатель on the engine block.

Pressing of components should be made not later than in 30 minutes after hermetic drawing.

  1. Establish into place маслозаборник and tighten with demanded effort (7.0 9.8 Nanometers) four bolts of its fastening.
  1. Operating in the manner similar described, put hermetic on an interfaced surface of a landing flange of the pallet, then press last to маслоотражателю, screw fixing bolts and, moving to a diagonal order from the centre outside (see an illustration), in stages tighten them with demanded effort (7.0 9.5 Nanometers). Cut off supporting limits of a back cover a lining, - try not to damage an interfaced surface of a cover.
  1. The further installation is made in an order, the return to an order of dismantle of components. Do not forget about necessity of observance of requirements of Specifications of the Head the Engine to efforts of a tightening of carving fixture.
  2. Fill in in the engine fresh engine oil.
  3. In summary start the engine and check up it on presence of signs of development of leaks through joints of the established components.