KIA Sportazh - Kia Sportage
Controls and operation receptions
Current leaving and service
The engine
   Check компрессионного pressure, an estimation of a condition of cylinders
   Check of the engine by means of the vacuum gauge
   Belts of a drive of auxiliary units
   Petrol models
      Greasing system - the general information, check of pressure of impellent oil
      Removal and engine installation
      Removal and installation of components of drive ГРМ
      Removal and installation of the inlet pipeline and final collector
      Service of a head of cylinders and components газораспределительного the mechanism
      Dismantling and assemblage of the block of cylinders, service of components
      Removal and pallet installation картера
      Removal, installation and service of the oil pump
      Removal and installation of a flywheel/privodnogo of a disk
      Removal and installation маслораспылителей
      Replacement of epiploons of a cranked shaft
   Diesel models
Systems of cooling, heating, ventilation and air conditioning
Power supply systems, managements of the engine/decrease of toxicity of the fulfilled gases and release of the fulfilled gases
Systems of an electric equipment of the engine
Five-step manual box of a gear change
Automatic transmission
Transmissionnaja line
Brake system
Suspension bracket and steering
Body
Onboard electric equipment
Control кузовные the sizes
Schemes of electric connections




Kia Sportage>> The engine>> Petrol models>> Removal and pallet installation картера

Removal and pallet installation картера

The given procedure is among those which performance does not demand removal of the engine from the car.

Removal

 PERFORMANCE ORDER

  1. Disconnect a negative wire from the battery.
  1. Turn out two top bolts of a rack of the inlet pipeline.
  1. Hang out the car over землней.
  2. Merge impellent oil (Current leaving and service see the Head), then screw into place and tighten with demanded effort a drain stopper, - in case of need replace its sealing washer.
  3. Prop up the forward bridge in gathering with карданном shaft.
  4. Turn out three bolts of fastening картера the forward bridge and remove the left plug of a support of its suspension bracket.
  5. Cautiously lower the bridge.
  1. Turn out fixing bolts and remove the intensifying kerchiefs, established with both parties of the engine, - for fastening of each kerchief it is used four bolts.
  1. Turn out corresponding bolts (3 + 4 шт) and remove protection panels картеров the engine and transmission.
  2. Turn out 19 bolts of fastening of the pallet картера the engine.
  3. Hooking thin шпателем, or other suitable tool, accurately separate the pallet from маслоотражателя, - try not to bend a fixing flange of the pallet and not to damage маслозаборную a tube.
Detail of installation of the pallet картера (3), маслозаборника (2) and маслоотражателя (1), - do not forget to check up a condition of a drain stopper (4).
  1. Turn out four fixing bolts and remove equipped with the mesh filter маслозаборник, - try not to bend маслоотражатель and not to damage маслозаборную a tube.
  2. Turn out one fixing bolt and remove маслоотражатель.
  3. Carefully clear interfaced surfaces of the removed components, completely having removed from them traces of oil, a dirt and the rests of old hermetic.
  4. Examine the pallet on presence of cracks, deformations and other mechanical damages. In case of need make corresponding regenerative repair, or replace the pallet.
  5. Estimate a condition of a drain stopper of the pallet, in case of need make its replacement.

It will be reasonable to replace a sealing washer of a drain stopper without dependence from its condition.

  1. Check up a condition маслоотражателя and the mesh filter маслозаборника. Carefully clean components, in case of revealing of irreversible damages make replacement.

Installation

The size выступания the pallet for borders of a face surface картера the engine should not exceed 1.5 mm.


 PERFORMANCE ORDER

  1. Impose a pillow of hermetic of type Loctite Ultra Blue 5900 on an interfaced surface of a landing flange маслоотражателя and press last to картеру the engine, the interfaced which surface also should be smoothed carefully out and degreased. Track, that hermetic was imposed from the interior of fixing apertures and with a tipping over on the ends. Screw a bolt of fastening of a plate and tighten it with demanded effort (9.5 Nanometers).
  1. Establish into place маслозаборник and tighten with demanded effort (9.5 Nanometers) four bolts of its fastening.
  1. Operating in the manner similar described, put hermetic on an interfaced surface of a landing flange of the pallet, then press last to маслоотражателю, screw 19 fixing bolts and, operating strictly in a certain order, in stages tighten them with demanded effort (9.5 Nanometers).
  1. The further installation is made in an order, the return to an order of dismantle of components. Do not forget about necessity of observance of requirements of Specifications of the Head the Engine to efforts of a tightening of carving fixture.
  2. Fill in in the engine fresh engine oil.
  3. In summary start the engine and check up it on presence of signs of development of leaks through joints of the established components.