KIA Sportazh - Kia Sportage
Controls and operation receptions
Current leaving and service
The engine
   Check компрессионного pressure, an estimation of a condition of cylinders
   Check of the engine by means of the vacuum gauge
   Belts of a drive of auxiliary units
   Petrol models
   Diesel models
      Greasing system - the general information
      Removal and engine installation
      Removal and installation of components of drive ГРМ
      Check and adjustment клапанных backlashes
      Removal and installation of the inlet pipeline and final collector
      Service of a head of cylinders and components газораспределительного the mechanism
      Dismantling and assemblage of the block of cylinders, service of components
      Removal and pallet installation картера
      Removal, installation and service of the oil pump
      Removal and installation маслоохладителя
      Removal and flywheel installation
      Removal and installation маслораспылителей
      Replacement of epiploons of a cranked shaft
Systems of cooling, heating, ventilation and air conditioning
Power supply systems, managements of the engine/decrease of toxicity of the fulfilled gases and release of the fulfilled gases
Systems of an electric equipment of the engine
Five-step manual box of a gear change
Automatic transmission
Transmissionnaja line
Brake system
Suspension bracket and steering
Body
Onboard electric equipment
Control кузовные the sizes
Schemes of electric connections




Kia Sportage>> The engine>> Diesel models>> Removal, installation and service of the oil pump

Removal, installation and service of the oil pump

Details of installation of the oil pump are shown on an illustration.

Design of the oil pump

1— The Screw
2— The Cover
3— The External gear wheel

4 — the Internal gear wheel
5 — Reduktsionnyj the valve
6 — the Forward epiploon of a cranked shaft
7 — the Case of pump assemblage


 PERFORMANCE ORDER

    Make dismantle disturbing to performance of procedure of components (corresponding sections in the present chapter see and Has undressed Removal and installation маслораспылителей in the Head Current leaving and service). Turn out fixing screws and remove the oil pump. Transfer pump assemblage on a workbench, turn out seven fixing screws and uncover (1).
    Having weakened by means of a shock screw-driver, turn out fixing screws and remove a back cover of pump assemblage.

Try at отпускании not to damage screws the pump case!

    Take internal and external gear wheels. Take a lock ring and remove components редукционного the valve (a saddle, a spring and плунжер). Take an epiploon, - the epiploon is subject to replacement without fail (the Section Replacement of epiploons of a cranked shaft see). Attentively examine the case and a pump cover, in case of revealing of cracks, deformations and other mechanical damages replace defective components. Estimate deterioration degree плунжера assemblages редукционного the valve, in case of need make its replacement. Check up a spring condition клапанной assemblages, in case of revealing of defects make replacement. Make control gaugings:
    Measure size axial люфта gear wheels.
    Measure sizes of backlashes between tops of teeths of gear wheels and a crescent insert.
    Measure size люфта landings of an external gear wheel in the working chamber of the case.
    Compare results of measurements to requirements of Specifications of the Head the Engine, in case of need make corresponding replacements. Assemblage is made as it should be the return to an order of dismantle of components. Before landing in pump assemblage grease the NEW epiploon with pure impellent oil. Track, that fixing screws have been tightened with demanded effort.
    Having greased литиевой with greasing of type NGLI No2, establish on pump assemblage the NEW sealing ring.
    Impose on an interfaced surface of pump assemblage a continuous pillow of hermetic. Press the pump on the engine and fix its bolts, having tightened the last with demanded effort (bolts М8: 16 23 Nanometers, bolts М10: 32 47 Nanometers). Remove supporting edge of a joint of components hermetic. The further installation is made in an order, the return to an order of dismantle of components. Do not forget about necessity of observance of requirements of Specifications of the Head the Engine to efforts of a tightening of carving fixture. Fill in in the engine fresh engine oil. Start the engine and check up it on presence of signs of development of leaks through joints of the established components.