KIA Sportazh - Kia Sportage
Controls and operation receptions
Current leaving and service
The engine
Systems of cooling, heating, ventilation and air conditioning
Power supply systems, managements of the engine/decrease of toxicity of the fulfilled gases and release of the fulfilled gases
Systems of an electric equipment of the engine
Five-step manual box of a gear change
Automatic transmission
Transmissionnaja line
Brake system
Suspension bracket and steering
Body
Onboard electric equipment
Control кузовные the sizes
Schemes of electric connections




Kia Sportage>> Control кузовные the sizes

Control кузовные the sizes

The general information

In motor industry two ways of removal of the control sizes between reference points of elements of a body/chassis can be used: direct and projective. The shortest distance is measured in the first case between chosen points on a straight line connecting them. In the second case the length of a projection of the given line on certain measured - usually horizontal - a plane is defined.

Two cores used in motor industry of a way of removal of the control sizes between reference points of elements of a body/chassis


More low in section the illustrative material on removal of the control sizes and tables of their rating values is resulted.

All cited data acts in film in the direct way if the opposite is not stipulated especially.

The control sizes передка bodies (all models)

AND, AND’ Apertures under back bolts of fastening of wings ( 10 mm)
IN, IN’ Apertures under forward болтыкрепления wings ( 10 mm)
WITH Nut of fastening of a brake line ( 6 mm)
D, D’ Nuts of fastening of block headlights ( 9.8 mm)
E, E’ Basic welding apertures (the left: 8х10 mm, right: 8 mm)
F Aperture under fastening of a plait of electroconducting ( 7 mm)


Gauging number 1 2 3 4 5 6 7 8 9
Rating value, mm 1293 696 1257 696 1452 930 1057 993 1103
Gauging number 10 11 12 13 14 15
Rating value, mm 995 1140 282 1000 282 1104

The lateral control sizes (5-door models)


AND The top basic aperture of the amplifier of a lateral beam ( 8 mm)
IN The bottom basic aperture of the amplifier of a lateral beam ( 7х10 mm)
WITH The top aperture under fastening of the top loopy lath of a forward door ( 12 mm)
D The bottom aperture under fastening of the bottom loopy lath of a forward door ( 12 mm)
E The top aperture under fastening of the top loopy lath of a back door ( 10 mm)
F The bottom aperture under fastening of the bottom loopy lath of a back door ( 12 mm)
G Aperture under fastening of the gauge-switch of a back door ( 15.8 mm)
Н Aperture under fastening of an overlay of a threshold of a back door ( 8.5 mm)
I Aperture under fastening of a back bumper

Gauging number 1 2 3 4 5 6 7 8 9
Rating value, mm 110 889 1992 2000 912 898 921 380 1113
Gauging number 10 11 12 13 14 15 16 17 18
Rating value, mm 1169 1177 1114 360 924 1493 763 991 1474
Gauging number 19 20 21 22
Rating value, mm 617 557 606 888

The internal control sizes And cabins (5-door models)

AND, AND’ The top apertures under fastening of plaits of electroconducting from the interior of racks (7 mm)
IN, IN’ The bottom apertures under fastening of plaits of electroconducting from the interior of racks ( 7 mm)
WITH, WITH’ Apertures under furnish fastening ( 14 mm)
D, D’ Apertures under fastening of the panel of a carpet covering of a floor ( 6 mm)
E, Е Apertures under fastening анкерных knots of seat belts ( 9 mm)
F, F’ Apertures under fastening of the module of a cooler ( 9 mm)
G, G’ Apertures under fastening of returnable mechanisms of seat belts ( 18 mm)
Н, Н Apertures under furnish fastening ( 6 mm)
I, I’ Apertures under fastening of drummers of locks of back doors ( 12 mm)
J, J’ Apertures under fastening of plaits of electroconducting ( 5 mm)

Gauging number 1 2 3 4 5 6 7 8 9 10
Nomina -
льное value, mm
1118 1317 1350 1340 1177 1350 1368 1026 1480 740

The internal control sizes In cabins (5-door models)


AND, AND ’; IN, IN ’; WITH, WITH ’; D, D ’; E, Е ’; F, F ’; G, G ’; Н, Н ’; J, J’ See above an illustration to gaugings And
I, I’ Basic welding apertures ( 10 mm)
TO Aperture under fastening of the lever of a lay brake ( 12 mm)

Gauging number 1 2 3 4 5 6 7 8 9 10
Nomina -
льное value, mm
1150 1162 1090 798 1158 978 718 1529 1103 1811

The internal control sizes From a cabin (5-door models, a left-hand side)

AND, AND ’; IN, IN ’; WITH, WITH ’; D, D ’; E, Е ’; F, F ’; G, G ’; Н, Н ’; I, I ’; J, J’ See above an illustration to gaugings In
TO Aperture under fastening анкерного seat belt knot (12 mm)

Gauging number 1 2 3 4 5 6 7 8 9 10
Nomina -
льное value, mm
1681 1936 1993 1589 1258 1129 1021 1031 605 1035

The internal control sizes From a cabin (5-door models, the right party)


AND, AND ’; IN, IN ’; WITH, WITH ’; D, D ’; E, Е ’; F, F ’; G, G ’; Н, Н ’; I, I ’; J, J ’; TO The left-hand side see above an illustration to gaugings With,

Gauging number 1 2 3 4 5 6 7 8 9 10
Nomina -
льное value, mm
1765 2022 2079 1695 1374 1275 1182 1153 852 1124

The control sizes of a back of a body (5-door models)


AND, AND’ Apertures under fastening of loopy laths (the left: 8х12 mm, right: 8 mm)
IN, IN’ Apertures under fastening of a telescopic emphasis ( 9 mm)
WITH, WITH’ Basic welding apertures ( 6.5 mm)
D, D’ Basic welding apertures (the left: 8х12 mm, right: 12 mm)
E Aperture under fastening of the drummer of the lock of a door of a back ( 12 mm)

Gauging number 1 2 3 4 5 6 7 8 9
Rating value, mm 725 1111 574 1303 1498 1037 1303 406 1230

The control sizes of a frame of the chassis (5-door models)

The gaugings made in the direct way


AND Apertures under fastening of basic arms of a body № 1 (the left: 28 mm, right: 24 mm)
IN Apertures in support of racks ( 65.6 mm)
WITH Apertures under fastening of basic arms of a body № 2 ( 28 mm)
D Drainage apertures ( 12 mm)
Е Apertures under fastening of basic arms of a body № 3 ( 28 mm)
F Drainage apertures ( 12 mm)
G Apertures under fastening of basic arms of a body № 4 (the left: 24х28 mm, right: 28х32 mm)

The gaugings made in the projective way


AND Apertures under fastening of basic arms of a body № 1 (the left: 28 mm, right: 24 mm)
IN Apertures in support of racks ( 65.6 mm)
WITH Apertures under fastening of basic arms of a body № 2 ( 28 mm)
D Drainage apertures (12 mm)
Е Basic beam of a fuel tank ( 42 mm)
F Apertures under fastening of basic arms of a body № 3 ( 28 mm)
G Cross-section a tank № 5 ( 68.5 mm)
Н Apertures under fastening of shock-absorbers ( 19 mm)
I Apertures under fastening of basic arms of a body № 4 (the left: 24х28 mm, right: 28х32 mm)