KIA Sportazh - Kia Sportage
Controls and operation receptions
Current leaving and service
The engine
Systems of cooling, heating, ventilation and air conditioning
Power supply systems, managements of the engine/decrease of toxicity of the fulfilled gases and release of the fulfilled gases
Systems of an electric equipment of the engine
Five-step manual box of a gear change
Automatic transmission
Transmissionnaja line
   The general information
   Coupling
      The general data
      Check and updating of level of a hydraulic liquid
      Check and adjustment of a pedal of coupling
      Removal and installation of a pedal of coupling
      Removal, service and installation of the main cylinder of a drive of deenergizing of coupling
      Removal, service and installation of the executive cylinder of a drive of deenergizing of coupling
      Removal, check of a condition and installation of components of coupling
   Distributing box
   Kardannye shaft
   Bridges
Brake system
Suspension bracket and steering
Body
Onboard electric equipment
Control кузовные the sizes
Schemes of electric connections




Kia Sportage>> Transmissionnaja line>> Coupling>> Removal, check of a condition and installation of components of coupling

Removal, check of a condition and installation of components of coupling

Basket and conducted disk of coupling

Removal

Details of installation of components of coupling are shown on illustrations the Design of the coupling applied on petrol models and the Design of coupling, applied on diesel models.

 PERFORMANCE ORDER

  1. By means of the special adaptation block a flywheel from проворачивания, then establish the tool for a centering of a conducted disk сцеплени.
  1. Release fixing bolts and separate a basket of coupling from a flywheel.

Coupling assemblage has considerable weight, - try not to admit its falling at отпускании last bolts.

  1. In case of need turn out eight fixing bolts and remove a flywheel (the Engine see the Head).
  1. For extraction from a pin of a cranked shaft of the directing bearing take advantage of a hammer with sliding the brisk.

Check

 PERFORMANCE ORDER

  1. Examine a working surface of a press disk on presence задиров, cracks and overheat traces, - insignificant defects can be eliminated by means of a fine-grained emery paper. Check up, are not broken off and whether погнуты petals диафрагменной springs. In case of need replace a basket.
  2. Estimate a condition of frictional overlays of a conducted disk and rivets of their fastening. Insignificant defects also can be eliminated by means of a fine-grained emery paper. At revealing of signs of easing of landing of rivets, and also in case of strong superficial pollution the disk is subject to replacement without fail.
  1. With the help колумбуса estimate degree of deterioration of frictional overlays, - the size заглубления heads of rivets should make not less than 0.3 mm.
  1. With the help плунжерного циферблатного a measuring instrument (DTI) define sizes cross-section and radial люфтов a disk. If results of measurements exceed limiting admissible values (Specifications of Head Transmissionnaja a line see), replace a disk.

Insignificant traces of corrosion can be eliminated by polishing by rigid felt.

Installation

 PERFORMANCE ORDER

  1. Installation is made in an order, the return to an order of dismantle of components, - before landing in a reception nest of a pin of a cranked shaft it is necessary to grease directing bearing литиевой with greasing (NGLI № 2), - запрессовывание the bearing is made by means of approaching оправки. Шлицы naves of a conducted disk are greased organic молибденсодержащей with greasing of type Mori White TA No.2, the centering is made by means of the special adaptation. Track observance of requirements of Specifications of Head Transmissionnaja a line to efforts of a tightening of carving fixture. In summary do not forget to take aligning adaptation and блокиратор a flywheel.

The vyzhimnoj bearing

Removal

 PERFORMANCE ORDER

  1. Remove выжимной the bearing from a primary shaft of a transmission.

Check

In order to avoid washing away of factory stuffing at all do not wash out выжимной the bearing in solvent!


 PERFORMANCE ORDER

  1. Manually check up freedom проворачивания the bearing in both directions, estimate degree of deterioration of the working surfaces contacting to a plug of deenergizing of coupling and диафрагменной by a spring of a press disk. The defective bearing replace.

Installation

 PERFORMANCE ORDER

  1. Grease surfaces of the bearing organic молибденсодержащей with greasing of type Mori White TA No.2, then plant it on the regular place in a dome of coupling and make sure of freedom of its rotation.