KIA Sportazh - Kia Sportage
Controls and operation receptions
Current leaving and service
The engine
Systems of cooling, heating, ventilation and air conditioning
Power supply systems, managements of the engine/decrease of toxicity of the fulfilled gases and release of the fulfilled gases
   Security measures and the general rules accepted at service of components of fuel paths of internal combustion engines
   The power supply system of petrol engines
      The general information
      Check and adjustment of quantity of turns of a single course/moment of ignition/concentration WITH
      Sbrasyvanie pressure in fuel system of the petrol engine, filling of a fuel path
      Power supply system checks
      Removal and installation of components of an inlet air path
      Removal and installation of a pedal of gas, adjustment of a cable of a drive throttle заслонки
      Removal and installation of a fuel tank
      Removal and installation of the fuel pump
      Removal and installation of the gauge of a stock of fuel
      Removal and installation kontrolno-zapornogo the valve
      Removal and installation of submitting and returnable lines of a fuel path
      Removal and installation of a jellied mouth of a fuel tank and separator of fuel evaporations
      Removal and installation of the filter of thin clearing of a fuel path
      Removal and installation of a regulator of pressure of fuel
      Removal and installation топливораспределительной highways
      Removal and installation of fuel injectors
   The power supply system of diesel engines
   Control systems of the engine and decrease in toxicity of the fulfilled gases
   System of release of the fulfilled gases
Systems of an electric equipment of the engine
Five-step manual box of a gear change
Automatic transmission
Transmissionnaja line
Brake system
Suspension bracket and steering
Body
Onboard electric equipment
Control кузовные the sizes
Schemes of electric connections




Kia Sportage>> Power supply systems, managements of the engine/decrease of toxicity of the fulfilled gases and release of the fulfilled gases>> The power supply system of petrol engines>> Removal and installation of a fuel tank

Removal and installation of a fuel tank

Gasoline is extremely inflammable, therefore at work with any components of fuel system it is necessary to accept special safety measures! Do not smoke, and do not come nearer to a place of work with open fire or the redurable not protected by a lamp shade. Do not make such works in the garages equipped with heating devices, working on natural gas (such, as водогреи, dryers, etc.)! The working platform should be ventilated well. At gasoline hit on a skin immediately wash off its water with soap. At carrying out of any works with fuel system put on goggles and hold near at hand the fire extinguisher. In case of a gasoline spillage immediately wipe a pool, but do not hold the rags impregnated with gasoline in places where the risk of its ignition is not excluded! The preventions resulted in Section of the Security measure and the general rules, accepted see also at service of components of fuel paths of internal combustion engines.

Details of installation of a fuel tank

 PERFORMANCE ORDER

    Disconnect a negative wire from the battery. Lift a back seat and unbend the rectangular valve of the panel of a carpet covering of a floor. Through a special service window disunite sockets of electroconducting of the fuel pump/gauge of a stock of fuel (see an illustration). Turn out the screw of fastening of the tyre of grounding.
    Turn out four fixing screws and uncover access to a fuel tank.
    Release fixing collars and disconnect from pump assemblage two fuel hoses. Disconnect electroconducting from the pressure gauge in a fuel tank. Through a service aperture release fixing collars and disconnect three fuel hoses from unions of assemblage of a tank. Release a collar of fastening of a jellied mouth of a fuel tank. Hang out the car over the earth. By means of the elevating equipment hang out assemblage of a fuel tank with a filter. Turn out 15-millimetric bolts of fastening of assemblage of a tank with a filter. Accurately separate a tank from elements of a frame of the car, lower it on the elevating equipment and transfer on a workbench. At once закупорьте open unions of a tank approaching заглушками for the purpose of the prevention of an exit outside of fuel evaporations.
    Turn out two fixing bolts and separate from a tank (1) filter (2).
    Installation is made upside-down. Track correctness of landing and reliability of fixing of fuel hoses on the unions, - hoses main, returnable and испарительной lines should stretch on unions a minimum on 25 mm, a jellied mouth - a minimum on 35 mm.