KIA Sportazh - Kia Sportage
Controls and operation receptions
Current leaving and service
The engine
Systems of cooling, heating, ventilation and air conditioning
Power supply systems, managements of the engine/decrease of toxicity of the fulfilled gases and release of the fulfilled gases
Systems of an electric equipment of the engine
Five-step manual box of a gear change
Automatic transmission
Transmissionnaja line
Brake system
Suspension bracket and steering
   The general information
   Estimation of a condition of components of a suspension bracket and steering drive
   Forward suspension bracket
      The general data
      Removal and installation of components of assemblage of the forward bridge
      Removal, check of a condition of components and installation of the stabilizer of cross-section stability
      Removal, service and installation of rack-mount assemblages
      Removal, service and installation of the top levers of a suspension bracket
      Removal, service and installation of the bottom levers of a suspension bracket
   Back suspension bracket
   Steering
   Suspension bracket geometry
Body
Onboard electric equipment
Control кузовные the sizes
Schemes of electric connections




augmentin cialis cheap cialis online purchase of cialis Kia Sportage>> Suspension bracket and steering>> Forward suspension bracket>> Removal, service and installation of rack-mount assemblages

Removal, service and installation of rack-mount assemblages

Removal

 PERFORMANCE ORDER

  1. Hang out the car over the earth.
  2. Remove forward wheels.
  3. Release a nut of fastening of a bar of the stabilizer of cross-section stability to the corresponding bottom lever of a suspension bracket (see Has undressed Removal, check of a condition of components and installation of the stabilizer of cross-section stability).
  1. Release a nut (1) axial bolts of fastening of a plug of rack-mount assemblage to the bottom lever of a suspension bracket.
  1. Take an axial bolt of a plug.
  1. Release coupling bolts and remove a plug (1) bottom support of rack-mount assemblage.
  1. Open a cowl and through an aperture in a mudguard of a wheel arch release three nuts of fastening of rack-mount assemblage to the basic block on a frame.
  1. Take rack-mount assemblage from a wheel arch.

Dismantling

Design of rack-mount assemblage of a forward suspension bracket

1 — the Nut
2 — the Top holder
3 — the Top insulator
4 — the Aligning washer
5 — the Top cup of a spring
6 — the Screw spring

7 — the Bottom insulator
8 — the Bottom holder
9 — Pylnik
10 — the Bottom saddle of a spring
11 — the Shock-absorber
12 — the Buffer of a course of compression


 PERFORMANCE ORDER

  1. Clamp a rack in a vice with soft sponges and on some turns release a nut of a piston rod of the shock-absorber, - do not remove a nut definitively.
  1. Clamp the bottom basis of rack-mount assemblage in a vice with soft sponges and by means of the special adaptation compress a screw spring.
  1. Turn away a nut of a piston rod and make rack dismantling.

Check

 PERFORMANCE ORDER

  1. Clamp the bottom part of the shock-absorber in a vice with soft sponges and manually check up smoothness and uniformity of a piston stroke of the shock-absorber in both directions.
  1. Having rocked a piston rod not less than three times, make sure of absence of signs of development of leaks.
  2. Visually estimate a condition of a screw spring.
  3. Check up on presence of damages the top cup and the bottom saddle of a spring, also estimate a condition of the top and bottom rubber insulators.

Assemblage

 PERFORMANCE ORDER

  1. Operating in an order, the return to a dismantle order, establish into place components of rack-mount assemblage, - track correctness of landing and - where it is required - input in gearing of all elements.
  2. Compress a screw spring and freely screw a nut of a piston rod.
  3. Clamp rack-mount assemblage in a vice with soft sponges and tighten a nut of a piston rod with demanded effort (37 ч 46 Nanometers).

Installation

 PERFORMANCE ORDER

  1. Installation is made in an order, the return to an order of dismantle of components, - track observance of requirements of Specifications of the Head the Suspension bracket and a steering to efforts of a tightening of carving fixture.

The definitive tightening of fixture of a rack is made after car lowering on the earth.

  1. In summary drive away the car in a workshop of car-care centre for check and adjustment of corners of installation of forward wheels (the Section Check and adjustment of corners of installation of forward wheels see).