KIA Sportazh - Kia Sportage
Controls and operation receptions
Current leaving and service
The engine
Systems of cooling, heating, ventilation and air conditioning
Power supply systems, managements of the engine/decrease of toxicity of the fulfilled gases and release of the fulfilled gases
Systems of an electric equipment of the engine
Five-step manual box of a gear change
Automatic transmission
Transmissionnaja line
Brake system
Suspension bracket and steering
   The general information
   Estimation of a condition of components of a suspension bracket and steering drive
   Forward suspension bracket
      The general data
      Removal and installation of components of assemblage of the forward bridge
      Removal, check of a condition of components and installation of the stabilizer of cross-section stability
      Removal, service and installation of rack-mount assemblages
      Removal, service and installation of the top levers of a suspension bracket
      Removal, service and installation of the bottom levers of a suspension bracket
   Back suspension bracket
   Steering
   Suspension bracket geometry
Body
Onboard electric equipment
Control кузовные the sizes
Schemes of electric connections



Kia Sportage>> Suspension bracket and steering>> Forward suspension bracket>> Removal, service and installation of the bottom levers of a suspension bracket

Removal, service and installation of the bottom levers of a suspension bracket

Removal

All models

 PERFORMANCE ORDER

  1. Hang out the car over the earth.
  2. Remove forward wheels.
  3. Remove the stabilizer of cross-section stability (the Section of System of an electric equipment of the engine see).
  4. Release a fixing nut and take an axial bolt of fastening to the bottom lever of a basic plug of rack-mount assemblage (see Has undressed Removal, service and installation of rack-mount assemblages).
  5. Disconnect from a rotary fist a tip of steering draught (the Part the Steering see).
  6. Release a coupling bolt and liberate from a rotary fist a finger of a spherical support of the top lever of a suspension bracket (see Has undressed Removal, service and installation of the top levers of a suspension bracket).

Models 4 х 4

 PERFORMANCE ORDER

  1. Turn out bolts (2) fastenings of the bottom spherical support to lever assemblage (1).
  1. Remove a rotary fist in gathering with a power shaft (the line see Head Transmissionnaja).
  1. Take шплинт, release корончатую a nut and by means of a special stripper liberate a spherical support (1) of a rotary fist.

Models 4 х 2

 PERFORMANCE ORDER

  1. Take шплинт, release корончатую a nut and by means of a stripper liberate a spherical support from assemblage of a rotary fist, - in case of need the spherical support can be dismantled from lever assemblage after removal of last from the car.

  1. The spherical support is fixed in a rotary fist by means of корончатой nuts (1) (models 4 х 2).
  1. Выпрессовывание the bottom spherical support from a rotary fist (model 4 х 2).

All models

 PERFORMANCE ORDER

  1. Release nuts шпиндельных bolts (2), take the last and remove lever assemblage (1) from the car.

Service

 PERFORMANCE ORDER

  1. Examine on presence of deformations, cracks and other mechanical damages the bottom lever of a suspension bracket and an axial finger of fastening to it of a basic plug of rack-mount assemblage. Estimate a condition rubber шпиндельных plugs and пыльника a spherical support and a spherical tip of a head of an axial bolt. Defective components replace.
  1. Выпрессовывание and запрессовывание rubber шпиндельных plugs it is made by means of the special adaptation, - before installation it is necessary to moisten the new plug with a soap solution.
  1. Spherical in case of need the support is replaced in gathering, no less than an axial finger of fastening of the basic plug of rack-mount assemblage.

Installation

 PERFORMANCE ORDER

  1. Installation is made upside-down, - track observance of requirements of Specifications of the Head the Suspension bracket and a steering to efforts of a tightening of carving fixture.