KIA Sportazh - Kia Sportage
Controls and operation receptions
Current leaving and service
The engine
Systems of cooling, heating, ventilation and air conditioning
   The general information
   System of cooling of the engine
      Cooling liquid - the general data
      Replacement of a cooling liquid - broad-brush observations
      Tightness check, replacement of hoses of system of cooling
      Thermostat check
      Check of serviceability of functioning муфты couplings of the fan of system of cooling
      Washing of a path of system of cooling
      Removal and thermostat installation
      Removal, check of a condition and installation of a radiator of system of cooling, replacement радиаторных hoses
      Removal and installation of a broad tank
      Removal and installation перепускного a branch pipe охладительного a path of the petrol engine
      Replacement of the bearing of a drive of the fan of system of cooling
      Removal, installation and service of the water pump
   Systems of ventilation, heating and air conditioning
Power supply systems, managements of the engine/decrease of toxicity of the fulfilled gases and release of the fulfilled gases
Systems of an electric equipment of the engine
Five-step manual box of a gear change
Automatic transmission
Transmissionnaja line
Brake system
Suspension bracket and steering
Body
Onboard electric equipment
Control кузовные the sizes
Schemes of electric connections




Kia Sportage>> Systems of cooling, heating, ventilation and air conditioning>> System of cooling of the engine>> Removal, installation and service of the water pump

Removal, installation and service of the water pump

Petrol models

 PERFORMANCE ORDER

  1. The water pump established on petrol models is not maintainable and, - in case of revealing of signs of development of leaks in a kind потеков a cooling liquid around a cover of drive ГРМ, - is subject to replacement.
  2. Remove protection картера.
  3. Uncover a radiator.
  4. Open the drain gate and lower cooling liquid from a radiator in the prepared capacity of suitable volume.
  5. Remove top and bottom радиаторные hoses.
  6. Remove переливной a hose going from a jellied mouth of a radiator to a broad tank.
  7. Remove an air inlet of an inlet air path (Power supply systems, managements of the engine/decrease of toxicity of the fulfilled gases and release of the fulfilled gases see).
  8. Remove крыльчатку the fan, and also a casing вентиляторной assemblages.
  9. Release fixing and adjusting bolts of the generator, then remove a belt of a drive of the generator.
1 — 4-costal приводной a belt
2 — the Adjusting bolt
  1. Remove a pulley of a drive of the fan of system of cooling (the Section Replacement of the bearing of a drive of the fan of system of cooling see).
  2. Remove подшипниковую fan assemblage (the Section Replacement of the bearing of a drive of the fan of system of cooling see).
  3. Remove the top and bottom covers of drive ГРМ (the Engine see the Head).
  4. Turning a cranked shaft in a normal direction, result the piston of the first cylinder in position ВМТ of the end of a step of compression.
  5. Release a lock bolt, take away a roller натяжителя from a tape газораспределительного a belt, then again tighten a lock bolt.
  6. Remove from a cogwheel of a drive of the water pump and take aside газораспределительный a belt.
  7. Again release a bolt натяжителя.
  8. Turn out fixing bolts and remove assemblage of the water pump.
1 — Covers of drive ГРМ with sealing elements
2 — the Intermediate roller
3 — Assemblage of the water pump
4 — the Sealing lining
  1. Remove from pump assemblage an intermediate roller.
  2. Carefully smooth out interfaced surfaces of the pump and the engine block.
  3. Installation is made in an order, the return to an order of dismantle of components, - track observance of requirements of Specifications of the Head of System of cooling, heating, ventilation and an air conditioning to efforts of a tightening of carving fixture.
  4. In summary start the engine and check up it on presence of signs of development of leaks of a cooling liquid. In case of need make corresponding corrections, modify heat-carrier level.

Diesel models

Removal and installation

Details of installation of the water pump of system of cooling of the diesel engine

1 — Top радиаторный a hose
2 — the Casing of the fan of system of cooling
3 — Krylchatka and приводной a fan pulley
4 — Belts of a drive of the generator and compressor K/V
5 — the Generator
6 — Natjazhitel of a belt of a drive of compressor K/V

7 — the Pulley of a cranked shaft
8 — the Top and bottom sections of a cover of drive ГРМ
9 — Natjazhitel газораспределительного a belt with a spring
10 — Gazoraspredelitelnyj a belt
11 — Bottom радиаторный a hose
12 — a heater Hose
13 — Assemblage of the water pump with a tension lath of the generator


 PERFORMANCE ORDER

  1. Turning a cranked shaft in a normal direction, result the piston of the first cylinder in position ВМТ of the end of a step of compression.
  2. Empty cooling system (Current leaving and service see the Head).
  3. Details of installation of the water pump are shown, - dismantle components as their numbering.
  4. Installation is made upside-down. Track observance of requirements of Specifications of the Head of System of cooling, heating, ventilation and an air conditioning to efforts of a tightening of carving fixture.

Service

Design of the water pump of system of cooling of the diesel engine
1 — the Cover
2 — the Sealing lining
3 — the Case

 PERFORMANCE ORDER

  1. In case of need the water pump can be disassembled for the purpose of check of a condition of its internal components and replacement of a sealing lining.
  2. The design of the water pump is shown, - operate as numbering of components.

It is not necessary to make dismantling of the case of the water pump! In case of need the case is replaced in gathering with internal components.

  1. Assemblage is made in обратом an order.