|
|
Kia Sportage>> The engine>> Petrol models>> Replacement of epiploons of a cranked shaft
Replacement of epiploons of a cranked shaft
|
|
The given procedure is among those which performance does not demand removal of the engine from the car. |
Forward epiploon
|
|
Disconnect a negative wire from the battery.
Turn out four fixing bolts and remove protection картера the engine.
Merge impellent oil (Current leaving and service see the Head).
Remove a belt of drive ГРМ (Current leaving and service see the Head).
Turn out a fixing bolt and remove from a cranked shaft a cogwheel of drive ГРМ, - in case of need take advantage of a stripper intended for dismantle of a steering wheel.
Take from a groove in a pin of a cranked shaft segment шпонку.
Having taken advantage of a knife with a thin flexible edge, cut a face surface of an epiploon.
|
|
Having hooked the wrapped up soft rags a screw-driver, take an epiploon from the landing nest in the case of the oil pump (1).
|
Remove assemblage of the oil pump (see Has undressed Removal, installation and service of the oil pump) and manually fill a new epiploon in a landing nest in its case.
|
|
By means of a press and approaching оправки plant an epiploon in a nest заподлицо with a surface of the case of the pump, - rest оправку only against a firm face surface of an epiploon.
|
The further installation is made in an order, the return to an order of dismantle of components. Do not forget about necessity of observance of requirements of Specifications of the Head the Engine to efforts of a tightening of carving fixture.
Fill in in the engine fresh engine oil.
Start the engine and check up tightness of landing of an epiploon.
In summary check up correctness of installation of a corner of an advancing of ignition (see the Head of System of an electric equipment of the engine), in case of need make necessary corrections (correct landing of a belt of drive ГРМ, having tracked correctness of combination of adjusting labels, - Current leaving and service see the Head).
|
|
Back epiploon
|
|
Disconnect a negative wire from the battery.
Hang out the car over the earth.
Remove transmission (the Five-step manual box of a gear change or Automatic transmission see the Head).
On models with Manual transmission remove coupling assemblage (the line see Head Transmissionnaja).
By means of the special adaptation block a flywheel/privodnoj a disk from проворачивания (see an illustration)
Turn out six fixing bolts and remove a flywheel/privodnoj a disk.
Turn out six fixing bolts and remove a back cover of the engine.
|
|
Having hooked a suitable screw-driver, take an old epiploon from the landing nest.
|
Estimate a condition of a gear wreath of a flywheel/privodnogo of a disk and coupling components (model with Manual transmission). Replace defective components.
Slightly grease sealing edges of the NEW epiploon and a wall of a landing nest in a back cover of the engine with pure impellent oil.
|
|
Accurately fill an epiploon (1) in a nest of a cover (2).
|
|
|
By means of a press and approaching оправки plant an epiploon in a nest заподлицо with a cover surface, - rest оправку only against a firm face surface of an epiploon.
|
Establish into place a back cover and fix its bolts.
Establish a flywheel/privodnoj a disk. Having greased a carving part of preliminary smoothed out fixing bolts with hermetic, fix them a flywheel/privodnoj a disk, having blocked it from проворачивания by means of the special adaptation (see an illustration), - bolts are tightened in three stages with strict observance of requirements of Specifications of the Head the Engine.
|
|
The carving part of fixing bolts should be completely cleared of old hermetic, - if to achieve absolute clearing it is not possible, it is necessary to replace a corresponding bolt. |
The further installation is made in an order, the return to an order of dismantle of components. Do not forget about necessity of observance of requirements of Specifications of the Head the Engine to efforts of a tightening of carving fixture.
Fill in in the engine fresh engine oil.
Start the engine and check up tightness of landing of an epiploon.
|
|
|
|