KIA Sportazh - Kia Sportage
Controls and operation receptions
Current leaving and service
The engine
   Check компрессионного pressure, an estimation of a condition of cylinders
   Check of the engine by means of the vacuum gauge
   Belts of a drive of auxiliary units
   Petrol models
      Greasing system - the general information, check of pressure of impellent oil
      Removal and engine installation
      Removal and installation of components of drive ГРМ
      Removal and installation of the inlet pipeline and final collector
      Service of a head of cylinders and components газораспределительного the mechanism
      Dismantling and assemblage of the block of cylinders, service of components
      Removal and pallet installation картера
      Removal, installation and service of the oil pump
      Removal and installation of a flywheel/privodnogo of a disk
      Removal and installation маслораспылителей
      Replacement of epiploons of a cranked shaft
   Diesel models
Systems of cooling, heating, ventilation and air conditioning
Power supply systems, managements of the engine/decrease of toxicity of the fulfilled gases and release of the fulfilled gases
Systems of an electric equipment of the engine
Five-step manual box of a gear change
Automatic transmission
Transmissionnaja line
Brake system
Suspension bracket and steering
Body
Onboard electric equipment
Control кузовные the sizes
Schemes of electric connections

Kia Sportage>> The engine>> Petrol models>> Removal and engine installation

Removal and engine installation

Removal

 PERFORMANCE ORDER

    Disconnect a negative wire from the battery. At a corresponding complete set remove protection картера the engine/transmission. Empty cooling system (Current leaving and service see the Head). Merge impellent oil (Current leaving and service see the Head). Remove an air inlet and an air sleeve (Power supply systems, managements of the engine/decrease of toxicity of the fulfilled gases and release of the fulfilled gases see). Remove components of a drive throttle заслонки (Power supply systems, managements of the engine/decrease of toxicity of the fulfilled gases and release of the fulfilled gases see). Remove the top and bottom hoses of a radiator of system of cooling (see the Head of System of cooling, heating, ventilation and an air conditioning). Disconnect a reception pipe of system of release of the fulfilled gases (Power supply systems, managements of the engine/decrease of toxicity of the fulfilled gases and release of the fulfilled gases see). Disunite all electric sockets located in an impellent compartment: a starter, the generator, ignition coils, муфта compressor K/V, fuel injectors, a ljambda-probe () (depending on a complete set), the gauge of position of a cranked shaft (models with АТ, - on models with Manual transmission electroconducting is disconnected from gauge CKP from under the car), the gauge of measurement of weight of air (MAF), the generator, the gauge of position throttle заслонки (TPS), the valve of a purge of a coal adsorber, the valve-regulator of turns of idling (IAC), and so forth Disconnect from the engine all vacuum hoses, including lines of strengthening of brakes and a switching drive ступичных муфт forward wheels (at a corresponding complete set), and also hoses охладительного and fuel paths (do not forget about a hose of tap of fuel evaporations on assemblage of a coal adsorber).

Before a detachment of fuel hoses do not forget to dump pressure in a path of system of injection of fuel (see the Head of the Power supply system, management of the engine/decrease of toxicity of the fulfilled gases and release of the fulfilled gases)!

    Remove a forward lattice (the Body see the Head). On models of a corresponding complete set remove condenser K/V fan, then actually condenser K/V (see the Head of System of cooling, heating, ventilation and an air conditioning). Remove a radiator of system of cooling (see the Head of System of cooling, heating, ventilation and an air conditioning).
    On models of a corresponding complete set lift the receiver compressor K/V.
    Remove belts of a drive of auxiliary units (see Has undressed Belts of a drive of auxiliary units). From under the car disconnect electroconducting of gauges of speed of movement (VSS) and CKP (models with Manual transmission), and also gauges-switches of fires of a backing and the alarm indicator of activation of an all-wheel drive mode.
Site of sockets of electroconducting of gauges VSS (), CKP (D) and gauges-switches of fires of a backing () and the alarm indicator of activation of an all-wheel drive mode () - models with Manual transmission.
Site of a socket of electroconducting of gauge VSS - models with АТ.
Site of sockets of electroconducting of gauges-switches of fires of a backing (1) and the alarm indicator of activation of an all-wheel drive mode (2) - models with АТ.
    Remove the gauge-switch of the alarm indicator of a full drive.
    Remove a starter (see the Head of System of an electric equipment of the engine).
    Prop up a basic beam of transmission / a distributing box a suitable jack, then turn out bolts of fastening RKPP/AT to the engine (the Five-step manual box of a gear change or Automatic transmission see the Head).
    Turn out bolts of fastening of a beam and lower transmission on a jack. Fix lifting slings in elevating eyes of the engine and hang out last so that support of its suspension bracket have appeared completely are unloaded. Turn out bolts of fastening of support and at the top cautiously take the engine from a motor compartment of the car.

Installation

 PERFORMANCE ORDER

    Installation is made in an order, the return to an order of dismantle of components. Track correctness of restoration initial connections of all lines of communication. Remember that all carving fixture should be tightened with demanded effort.