|
|
|
|
KIA Sportazh - Kia Sportage
Controls and operation receptions
Current leaving and service
The engine
Systems of cooling, heating, ventilation and air conditioning
Power supply systems, managements of the engine/decrease of toxicity of the fulfilled gases and release of the fulfilled gases
Systems of an electric equipment of the engine
Five-step manual box of a gear change
Automatic transmission
Transmissionnaja line
Brake system
Suspension bracket and steering
Body
Onboard electric equipment
The general information and safety measures
Search of causes of failures of an electric equipment
Safety locks - the general information
Chain breakers - the general information
The relay - the general information and check of serviceability of functioning
Assembly blocks of safety locks/relays - the general information, removal, installation, replacement of safety locks
System of timers and alarm gongs (ETWIS) - the general information, removal and installation of the operating module
Check of serviceability of functioning of the switch of ignition
Check of serviceability of functioning подрулевых switches
Check of serviceability of functioning of operating switches and drive electromotors стеклоподъемников
Check of serviceability of functioning of the operating switch and electromotors of adjustment of door rear-view mirrors
Salonnye fixtures - replacement of lamps, check of serviceability of functioning
Replacement of lamps and check of serviceability of functioning of external lighting devices
Removal, check of serviceability of functioning and installation of the breaker of indexes of turns/alarm systems
Removal, installation and adjustment of block headlights
Safety pillows - the general information and safety measures
Switching-off SRS
Reading of codes of malfunction DTC
Removal and installation of the module of a driver's pillow of safety
Removal, installation and adjustment of a contact cable drum of the module of a driver's pillow of safety
Removal and installation of the diagnostic module of pillows of safety (ADU)
Control кузовные the sizes
Schemes of electric connections
|
|
|
|
Kia Sportage>> Onboard electric equipment>> Replacement of lamps and check of serviceability of functioning of external lighting devices
Replacement of lamps and check of serviceability of functioning of external lighting devices
Headlights
Replacement of lamps
|
|
Galogennye lamps are filled by gas being under pressure and at damage can "blow up"! Try not to touch a lamp flask barehanded, - the fatty stains left on glass can be at the bottom of a lamp exit out of operation as a result of a local overheat. With a view of additional safety at service галогенных lamps it is necessary to put on goggles! |
|
|
Open a cowl.
|
|
Disconnect brought to the back party of a block headlight electroconducting.
|
|
|
Dismantle rubber пыльник.
|
|
|
Release a wire spring clamp.
|
Liberate a lamp from three grooves in assemblage of a block headlight and establish instead of it replaceable.
Assemblage is made in an order, the return to an order of dismantle of components, - track reliability of fixing of components.
|
|
Check of serviceability of functioning of the switch of a choice of a mode of functioning of headlights
|
|
By means of an ohmmeter check up correctness of distribution of conductivity between plugs of a contact socket of electroconducting of a block headlight from outside a plait in various positions of the lever left подрулевого the switch (see the table). In case of need make corresponding corrections/replace assemblage подрулевых switches.
Check of serviceability of functioning of the switch of a choice of a mode of functioning of headlights
|
|
The forward combined lanterns
Replacement of lamps
|
|
The forward combined lanterns are located from lateral aspects of block headlights and carry out a role of indexes of turns and parking/dimensional fires.
|
|
Open a cowl and find in a corresponding corner of an impellent compartment a white plastic ring.
|
Having pulled for a ring, liberate from a mudguard covered a spring clamp.
Accurately remove assemblage of the forward combined lantern.
|
|
Having turned counter-clockwise before combination of lock uvulas with reciprocal grooves, take from lantern assemblage a cartridge with the lamp planted in it.
|
Having pressed and having turned equipped байонетным a socle a lamp, take it from a cartridge.
Plant in a cartridge a replaceable lamp and make lantern assemblage, - operate in an order, the return to an order of dismantle of components.
|
|
For защелкивания a spring clamp of assemblage again pull for a plastic ring. |
|
|
Check of serviceability of functioning of switches of indexes of turns / dimensional fires
|
|
By means of an ohmmeter check up correctness of distribution of conductivity between plugs of a contact socket of electroconducting of the forward combined lantern from outside a plait in various positions of the lever left подрулевого the switch (see the table). In case of need make corresponding corrections/replace assemblage подрулевых switches.
Check of serviceability of functioning of switches of forward indexes of turn / dimensional fires
|
|
Top level Stoplight
Lamp replacement
5-door models
|
|
|
|
By means of a small screw-driver cautiously drown the central pins of fixing clamps of a back cover of a stoplight of top level.
|
Take clamps and uncover, - try not to lose components of clamps.
|
|
Having turned on 1/4 turns counter-clockwise, liberate a cartridge with the lamp established in it from a reflector of lantern assemblage.
|
Having pulled, take a paw from a cartridge and establish on its place the replaceable.
Assemblage is made in an order, the return to an order of dismantle of components.
|
|
Models the Cabriolet
|
|
|
|
Turn out fixing screws and remove a lens of lantern assemblage.
|
|
|
Accurately take a lantern from a casing and, having turned a cartridge on 1/4 turns counter-clockwise, liberate it from a reflector.
|
Having pressed and having turned, take equipped with a socle байонетного type a lamp from a cartridge and establish on its place the replaceable.
Assemblage is made in an order, the return to an order of dismantle of components.
|
|
The back combined lanterns
Replacement of lamps
5-door models
|
|
|
|
Having pulled on itself for the provided dredging, accurately uncover access to a back loudspeaker.
|
Having wrung out a lock uvula, disunite a contact socket of electroconducting.
|
|
Give four nuts of fastening of lantern assemblage.
|
|
|
Remove a lantern with кузовной car panels.
|
|
|
Having combined lock uvulas with reciprocal grooves, take the failed lamp and establish on its place the replaceable.
|
Assemblage is made in an order, the return to an order of dismantle of components.
|
|
Models the Cabriolet
|
|
|
|
Uncover access to the back combined lantern.
|
|
|
Having wrung out a lock uvula, disunite a contact socket of electroconducting, then release four fixing nuts and remove lantern assemblage.
|
|
|
Having combined lock uvulas with reciprocal grooves, take the failed lamp and establish on its place the replaceable.
|
Assemblage is made in an order, the return to an order of dismantle of components.
|
|
Check
All models
|
|
By means of an ohmmeter check up correctness of distribution of conductivity between plugs of a contact socket of electroconducting of the back combined lantern from outside a plait in various positions of corresponding switches/gauges-switches (see the table). In case of need make corresponding corrections/replace the failed elements.
Check of serviceability of functioning of switches/gauges-switches of activation of lamps of the back combined lanterns
|
|
Lanterns of illumination of licence plate
Design and details of installation of lanterns of illumination of licence plate
Replacement of lamps
|
|
Turn out two fixing screws and remove a lens of a faulty lantern of illumination of licence plate.
|
|
Having pulled downwards, liberate from lantern assemblage ламподержатель, then take (also simply pull a lamp downwards) from it fused lamp and establish on its place the replaceable.
|
Establish into place ламподержатель and a lens, screw fixing screws.
|
|
|
|