KIA Sportazh - Kia Sportage
Controls and operation receptions
Current leaving and service
The engine
Systems of cooling, heating, ventilation and air conditioning
Power supply systems, managements of the engine/decrease of toxicity of the fulfilled gases and release of the fulfilled gases
Systems of an electric equipment of the engine
   System of ignition of the petrol engine
   System of simplification of cold start of the diesel engine
   Charge and start systems
      The general information
      The storage battery - the general information, recommendations about service
      Charge system - the general data and security measures
      Checks of system of a charge
      Removal and generator installation
      System of start of the engine - the general data and security measures
      Removal and starter installation
      Check and replacement of the gauge-switch of disconnection of a chain of a starter (CPP) on models with Manual transmission
Five-step manual box of a gear change
Automatic transmission
Transmissionnaja line
Brake system
Suspension bracket and steering
Body
Onboard electric equipment
Control кузовные the sizes
Schemes of electric connections




Kia Sportage>> Systems of an electric equipment of the engine>> Charge and start systems>> Removal and starter installation

Removal and starter installation

Petrol models

Removal

 PERFORMANCE ORDER

  1. Disconnect a negative wire from the battery.
  2. Turn out two top bolts of fastening of a basic arm of the inlet pipeline.
  3. Hang out the car over the earth.
  1. On models with Manual transmission turn out two fixing bolts and take aside the executive cylinder of coupling.
  1. Turn out two bottom fixing bolts and remove a basic arm of the inlet pipeline.
  1. Turn out two top bolts of fastening of a starter.
  1. Turn out the bottom fixing bolt, liberate a starter from a coupling dome (model with Manual transmission) / the hydrotransformer (model with АТ) and, having propped up, fix it in an impellent compartment.
  2. Lower the car on the earth.
  3. From above disconnect electroconducting from starter plug S.
  1. Release a fixing nut and disconnect electroconducting from the plug In (1) starters, - do not drop a lock washer.
  1. Again lift the car, take aside a plait of electroconducting of transmission and through a bottom take a starter from an impellent compartment.

Installation

 PERFORMANCE ORDER

  1. Get a starter in an impellent compartment.
  2. Lower the car on the earth and connect electroconducting to the plug In a starter, - do not forget to plant a lock washer, track reliability of a tightening of a nut.
  3. Connect electroconducting to plug S.
  1. Get on a regular place a basic arm of the inlet pipeline and fix its two top bolts.
  1. Lift the car and get a starter on the regular place.
  2. Screw at first two top fixing bolts, then bottom.
  3. Level a starter, then tighten three fixing bolts with demanded effort (37 54 Nanometers).
  4. Screw and tighten with demanded effort (37 54 Nanometers) the bottom bolts of fastening of a basic arm of the inlet pipeline.
  5. On models with Manual transmission establish into place the executive cylinder of coupling, - the effort of a tightening of fixing bolts also makes 37 54 Nanometers.
  6. Lower the car on the earth and tighten with demanded effort (37 54 Nanometers) the top bolts of a basic arm of the inlet pipeline.

Diesel models

Details of installation of a starter on diesel models

 PERFORMANCE ORDER

  1. Disconnect a negative wire from the battery.
  2. Turn out the top bolts of fastening of a starter.
  3. Hang out the car over the earth.
  4. Disconnect electroconducting from plugs In and S a starter, - try not to lose a lock washer at отпускании a fixing nut of the plug of Century
  5. Turn out the bottom fixing bolts and remove a starter.
  6. Installation is made upside-down, - track observance of requirements of Specifications of the Head of System of an electric equipment of the engine to efforts of a tightening of carving fixture.