KIA Sportazh - Kia Sportage
Controls and operation receptions
Current leaving and service
The engine
Systems of cooling, heating, ventilation and air conditioning
Power supply systems, managements of the engine/decrease of toxicity of the fulfilled gases and release of the fulfilled gases
Systems of an electric equipment of the engine
Five-step manual box of a gear change
Automatic transmission
Transmissionnaja line
Brake system
Suspension bracket and steering
Body
   The general information
   The external equipment and кузовные elements
   The salon equipment
      The panel of devices - the general information, removal and installation of components
      Removal and installation of the central console
      Seats - the general information, condition check, removal and installation of components
      Design and details of installation of components of seat belts, removal worked emergency натяжителей
      The scheme of an arrangement and detail of installation of panels of furnish of salon
Onboard electric equipment
Control кузовные the sizes
Schemes of electric connections




Kia Sportage>> Body>> The salon equipment>> Seats - the general information, condition check, removal and installation of components

Seats - the general information, condition check, removal and installation of components

Design and details of installation of components of seat belts are shown in Section the Design and details of installation of components of seat belts, removal worked emergency натяжителей.

The general information

Design and details of installation of seats

1 — the Lateral cover of the basis
2 — the Lever of adjustment of an inclination of a back
3 — the Lever of adjustment of a configuration of a lumbar emphasis of a back
4 — the Lever отпускания the mechanism of fixing of a sled

5 — Headrests
6, 10 — Backs
7, 11 — Pillows
8 — Loopy assemblages
9 — the Clamp

Forward seats

Forward seats are established separately and regulated in an individual order. A sled of each seat fastens to directing the frames attached to a floor of the car by means of three bolts and one nut each. Drive levers отпускания mechanisms of fixing of a sled are deduced under forward edges of pillows and allow to carry out adjustment of position of seats in a longitudinal direction. On one adjusting lever it is deduced on external edges of assemblages of seats, - procrastination of the handle of the lever upwards leads отпусканию a clamp of a back and allows to regulate an inclination of last by its compulsory отжимания downwards (at отпускании backs it is automatically translated in extreme forward position under the influence of a special spring). On the right the lever of adjustment of a configuration of a lumbar emphasis is located on a back of a driver's seat also.

Back seat

The back seat with a continuous pillow can be equipped both integral, and the back divided into two individual sections. Backs are equipped by the built in headrests. The pillow has loopy fastening to a floor that allows to throw back seat assemblage forward with its transfer in vertical position, - the back () should be lowered preliminary forward. Fastening of assemblage and to a floor is carried out by means of two bolts, two nuts and one back clamp. Back fixing (ок) in vertical position is provided with two built in in walls of a luggage space hooks.

Check

 PERFORMANCE ORDER

  1. Check up smoothness of a course of adjusting levers of forward seats, estimate degree of deterioration of components of fixing mechanisms. Defective details replace.
  2. Make sure of reliability of a tightening of all carving fixture, - in case of need tighten it with demanded effort.
  3. Grease mobile components of a sled, приводных levers and fixing mechanisms.

Removal and installation of components

Backs of forward seats

 PERFORMANCE ORDER

  1. Remove the lever handle отпускания the mechanism of fixing of a back.
  1. Dismantle decorative заглушки, turn out fixing bolts and remove a lateral cover of the basis of assemblage of a seat.
  1. On a driver's seat turn out the fixing screw and remove the lever of adjustment of a configuration of a lumbar emphasis of a back.
  1. Remove ring clamps of fastening of an upholstery of a back of a seat.
  1. Turn out a loopy bolt of fastening of a back.
  1. For the purpose of providing of access to fixture of a rotary fist of a back lift up upwards an upholstery of last.
  1. Turn out fixing bolts, remove a rotary fist and separate a back from a pillow.
  1. Installation is made upside-down, - track observance of requirements of Specifications the Body to efforts of a tightening of carving fixture.

Assemblage of a back seat

 PERFORMANCE ORDER

  1. Having extended the push-button clamps located outside from headrests, lower forward a back () seats.
  2. Turn out two fixing bolts and give two nuts of fastening of a pillow of a seat to a floor.
  3. Remove assemblage of a back seat and take it from the car.
  4. In case of need turn out loopy bolts and separate a back () from a pillow.
  5. Installation is made upside-down, - track observance of requirements of Specifications the Body to efforts of a tightening of carving fixture.